Customer Reviews

4.8 out of 5
Write a Review
  • All Reviews (64)
  • Image (3)
  • Video (0)
  • All Star
    • All Star(64)
    • 5 Star(56)
    • 4 Star(5)
    • 3 Star(2)
    • 2 Star(0)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
Show Original

A part of the review has been auto-translated.

  • 29/06/2016

    Good switching PSU. The voltage is adjustable from 10,5V to 13,9V. The ripple and the noise of the output voltage are good (tested with no load). No issues at all. Definitively recommended!

    Show Original
  • 27/10/2017

    Bon produit pour le prix.

    Show Original
  • 15/01/2016

    I got what I wanted to buy ! Easy to set up ! good value for money !

    Show Original
  • 06/08/2020

    Nice power supply for a DIY. A lot of things to do with this power supply

    Show Original
  • 10/08/2015

    Tested the power supply with LED-Strip (SKU159277) - as I wrote there in my review, the SKU159277 takes about 0,44A - so this is not a stress test for the 120W switching power supply ;-) But it works fine and the additional test with the PWM-Modul ("LED Light Dimmer", SKU015487) was satisfying too!

    Show Original
  • 11/07/2017

    This is my second unit. I am very satisfied with it for two reasons : - they stand the 10 amps current draw. This is not the case of many chinese power supplies - there is a little pot to adjust voltage. For modeler chargers using 13,8V like a full loaded car battery is safer than being just at 12 V ....and this unit is fanless !

    Show Original
  • 05/07/2017

    it's a nice power supply. I hooked it up to a very current consuming warm air blower unit and it held up. looks well made inside. only thing was I had to open it up because the screws of the heat sink were not tightly screwed. but that was just a matter of two screws for the casing then sliding it open. and tightening the heat sink. it put out 12.2 volts. nice. I don't know yet how to test the max current it will give. I'm pleased with the purchase.

    Show Original
  • 12/11/2015

    I use it for quite computer with itx module for ATX board. about 80W no problem. Use screw to correct 12V. from factory come as 10.9V. max i have 14V. good product, but for first users may be problemtic

    Show Original
  • 23/05/2015

    didn't think much about this before I ordered it I was going to use it to run one strip of lights now it's the power supply in my RV can be turned up to 14.3v does a great job of keeping the batteries charged

    Show Original
  • 28/11/2016

    I tested it with a consumption of 8.5A and it worked very well. I have had the good surprise to find a potentiometer that allows to trim the output voltage. A very good characteristic for modelers who need a voltage never lower than 12V. Output voltage is really independant from the current output.

    Show Original

    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • £3.30
    • £11.77
    • £5.10
    • £15.44
    • £53.30
    • £21.33
    • £4.29
    • £3.57
    • £6.23
    • £7.72
    • £1.79
    • £2.55
    • £2.86
    • £1.69
    • £2.43
    • £5.88
    • £1.10
    • £18.39