Customer Reviews

4.87 out of 5
See all 474 reviews
Write a Review
  • All Reviews (474)
  • Image (42)
  • Video (5)
  • All Star
    • All Star(474)
    • 5 Star(441)
    • 4 Star(17)
    • 3 Star(7)
    • 2 Star(4)
    • 1 Star(5)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
|
Show Original

A part of the review has been auto-translated.

  • 24/06/2017

    easy to use - comes with extra motor connection cable - only you must carefully solder this - 2A brushed built in esc works very smooth and good. It is my second low voltage DSM receiver from BG - Now flies in a 600mm wingspan OPEL RAK 1 two 1,7 gr. servos elev. / rudder and 8mm pusher brushed.

    Comments (4)
    Show Original
  • 24/05/2020

    Thanks to the feedback reviews I figured out how to bind to a Spektrum DSM2 DX8 Tx - ignore these instructions to use a bind plug - just attach a 1s battery & when the red Rx binding light changes from fast to slow - power up your Tx with bind button depressed on Tx - once bound you can fire up the Rx easily after switching on the Tx. I used a brushed motor as supplied in the Black Flyer V2 kit - you solder to the spare connectors from the the built in esc. You need to set Tx max low trim on the throttle & the motor response is good with satisfactory throttle range & power - I used BG 1g servos that plug in easily. Impressive Rx at great price - looking forward to fligh test soon - recommended ! 😊

    Comments (1)
    Show Original
  • 09/04/2018

    I use it with my DIY Whitehead. Integrated 2AESC works good with full Lipo on two paralell 720 brushed motors. But low voltage do not work in the way I hoped. At low voltage motors do not stop and the aileron servo begin to spin in various directions. So short flights 3- 4 minutes with a HV 3,V 230mah Lipo are fun enough.

    Comments (2)
    Show Original
  • 05/08/2017

    Bought this receiver together with 1.7g servos as recommended by BG for their Minimum Fokker E3. The servo and receiver have incompatible connectors and BG are unable to furnish information on the plug/socket types to enable fabrication of matched leads. None of the 3x items came with instructions or information although a Fokker build thread is on file. Found out that connectors are JST SH 1.0, not available at BG!!!!!!

    Comments
    Show Original
  • 02/10/2016

    receiver binds to my dx8, all channels ok. I soldered a 7mm micro brushed motor to the motor output of the receiver but it doesnt work. Motor is OK. Without ESC its worthless for me..

    Comments (5)
    Show Original
  • 19/09/2019

    This tinny rc work just dsm2 any tx.I use spektrum but step one plug battery, 2step blink rarely wait few seconds come blinking speed, 3 step open your tx in bind mid after that in 2 sec leds red becomes solid and voile means done can put for any toys plane or heli all connectors is 3pins i wiil lock on rc group forum what is any contact have for aileron ,rudder etc.

    Comments
    Show Original
  • 11/07/2017

    Passt genau zum "Robur" von Busch in 1:87. Armin

    Comments (3)
    Show Original
  • 10/06/2019

    I'm flying this micro receiver in a little plane made from 3mm sheet foam from discarded supermarket meat trays (styrofoam). The receiver binds easily with my Spektrum module/ Futaba radio. Motive power is a 8.5mm x 20mm coreless motor (Chaoli from BG) turning a 45mm propeller. 180ma LiPo provides several minutes of high speed fun outdoors in moderate conditions. The built-in 2A speed controller seems to have no problem with this combination even when running full throttle for almost the entire flight. The servo plugs on this receiver are the same as the E-Flite micro brick. I bought some of these connectors and spliced them on a couple of 1.7g micro servos to complete the system. The little plane is very lively in the air and really keeps you busy on the transmitter sticks! This is second time I have purchased one of these units and I'm happy with both of them.

    Comments
    Show Original
  • 17/07/2017

    This Rx for 3.7v low voltage is just great. you solder a 2-wire Coreless motor to it or plug in a 3-wire brushless motor. The connections are MINI MICRO 1.0 PH 3-PIN, so be sure your servos have these connectors (Orlandoo 1.7 come with the wrong connector and you have to adapt). The white ones from HEXTRONIK come with the right connector.. I've had to resolder the wires back on, they use a tiny gauge wire. I soldered on a 22 ga. wire nipple that doesn't bend with every movement or adjustment you make when stuffing the electrical parts in side an aircraft. For the price it's fair enough I bought a 2nd one to avoid changing all the time...

    Comments
    Show Original
  • 03/09/2020

    Works great I broke wire off beceause it wasnt secured first install I fixed it and am pleased with it binds with radiomaster TX16S and has salvaged a fun little slope fairy... Whippet old reciver burnt out!

    Comments (1)
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$18.89
    • US$11.44
    • US$26.07
    • US$9.99
    • US$220.49
    • US$136.49
    • US$8.39
    • US$38.84
    • US$40.76
    • US$94.49
    • US$262.49
    • US$75.99
    • US$419.99
    • US$43.20
    • US$100.79
    • US$139.64
    • US$76.64
    • US$19.99