Customer Reviews

4.88 out of 5
See all 41 reviews
Write a Review
  • All Reviews (41)
  • Image (7)
  • Video (0)
  • All Star
    • All Star(41)
    • 5 Star(36)
    • 4 Star(5)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
|
Show Original

A part of the review has been auto-translated.

  • 10/04/2024

    just speechless? NO!!!! I could write for hours on end about this amazing purchase but I will write them as soon as possible...armoured packaging.fast shipping.dream price.amazing product quality!assembly is relatively easy and I dealt with minimal problems 1 (before assembling the Z axis, check the X axis runner that it is well tightened) 2 (the terminal switch located on the left side is preferable to pass the cable through the channels that exist under the chassis) 3 (the cables that came from the controller and go to the X AND Z axis, you will have to remove 3 plastic caps from the plastic channel so that they can pass to the block of the X axis, otherwise there is a risk that the cables will be damaged during the movement of the Y axis. Attached photos) I ran the CNC with the EASEL software, which worked perfectly!!!! Thanks to BANGGOOD and TWO TREES for giving me the opportunity to buy this amazing tool at an amazing price!!! postscript. the motor you see in the photos is the upgrade and you buy it separately

    Comments
    Show Original
  • 30/04/2024

    I am satisfied with the product, very good for hobby use, good price, fast delivery. The screws are freed from vibration.

    Comments
    Show Original
  • 25/03/2024

    With a basic engine and with o-flute bits, I was able to successfully process uhmwpe boards. I recommend that you buy the 123 block to square machine, there are two motors for the Y-axis in open loop, without a calibrated block it is impossible to set them equal. I only miss original drawings for spoilboard and for Z axis atachment plate._And I was able to connect Universal G-code sender by wifi, and Putty using telnet protocol. MKS DLC board is capable to use 3d probe sensor, so CMM is in reach with custom support code by telnet or serial. I also must admit serious problem with disconects when conecting by USB cable, on GRBL forum they say, couse is CH340G USB to serial chip, to matingate this i run program by sdcard or by wifi.

    Comments
    Show Original
  • 18/03/2024

    Great Machine! Some parts could be improved but overall great value for price! and amazing delivery time!!

    Comments
    Show Original
  • 08/01/2024

    Fast delivery, well packed. Machine is well built and easy to assemble.

    Comments
    Show Original
  • 20/05/2024

    Arrived on time. There is a mistake in the description, it's only a nema 23 (no z) the others are nema 17. I haven't assembled it yet, I'll come back to give the exact feedback later.

    Comments
    Show Original
  • 26/05/2024

    Very nice machine very solid.

    Comments
    Show Original
  • 06/10/2023

    If you are looking for a good machine, you found it! I love this machine.

    Comments
    Show Original
  • 28/11/2023

    good value for money CNC milling machine for hobby use It is not a bad idea to use thread glue to prevent the screw from loosening

    Comments
    Show Original
  • 21/07/2023

    Product is in order, arrived on time. Putting it together from the video was simple. Unfortunately, some of the bolts had size issues, but with a small cut, they fit right. It's a massive good piece of equipment. In all respects, it's as described.

    Comments (5)
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$499.00
    • US$734.88
    • US$329.00
    • US$835.99
    • US$1,599.99
    • US$1,401.71
    • US$725.71
    • US$329.99
    • US$299.00
    • US$499.00