Precise details:
FlySky FS-SRM 2.4GHz ANT Protocol Mini RC Receiver PWM/PPM/i-BUS/S.BUS Output Compatible FS-ST8 Radio Transmitter for RC FPV Racing Drone
OVERVIEW:
FS-SRM based on ANT protocol is a new receiver with two external antennas and bidirectional transmission. It outputs PWM or PPM/i-BUS/S.BUS signal and has a compact design. The design of the receiver is easily to install, and it adapts multicopters.
Specifications:
Brand Name: FlySky
Item Name: FS-SRM RC Receiver
Model: FS-SRM
Adaptive transmitters: Transmitter with ANT protocol, such as FS-ST8
Adaptive Models: Multicopters
Numbers of Channels: 1
RF: 2.4GHz ISM
Maximum Power: < 20dBm (e.i.r.p.) (EU)
2.4G Protocol: ANT
Resolution: 1024
Antenna: Two antennas
Distance: >380m
Input Power: 3.5 ~ 9V/DC
Data Output: PWM/PPM/i-BUS/S.BUS
Online Update: Yes
Temperature Range: -10℃ ~ +60℃
Humidity Limit: 20% ~ 95%
Dimensions: 19*12.1*3mm
Weight: 1.1g
Certifications: CE, FCC ID: 2A2UNSRM00
Binding:
The receiver supports two -way binding and one-way binding. The transmitter will display the information returned from the
receiver after the two-way binding is completed.
Follow the steps below to bind in two-way binding:
Select [2 WAY] for RF standard of the transmitter, then put the transmitter into bind mode.
The receiver supports tho ways to enter bind mode: BIND button binding and BIND button binding after power-on.
- BIND button binding: Press and hold the BIND button of the receiver while powering on the receiver, tthe LED of the receiver
should be flashing, indicating that the receiver is in bind mode. Then release the BIND button.
- BIND button binding after power-on: The receiver has not been connected to the transmitter when it is powered on. Press and
hold the BIND button for 3 seconds, the LED of the receiver should be flashing, indicating that the receiver is in bind mode.
Then release the BIND button.
When the LED of the receiver is solid on, the binding process should be completed. The transmitter exits the bind mode
automaticlly.
Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any
problems arise.
Follow the steps below to bind in one-way binding:
Select [1 WAY] for RF standard of the transmitter, then put the transmitter into bind mode.
Put the receiver into bind mode ( Refer to the description above for entering bind mode).
When the LED of the receiver is in slow flashing state, the binding process should be completed. You need to manually put the
transmitter to exit the bind mode. Then the LED of the receiver is solid on, indicating that the binding is completed.
Check to make sure the transmitter and receiver functions are working correctly, repeat steps 1 to 3 (binding process) if any probems arise.
Firmware update:
The firmware of this receiver is updated through the FlyskyAssistant (Only version 3.0 or above is supported. The firmware of
FlyskyAssistant is available on the Flysky official website).
This receiver can be updated via the following two ways:
After the binding between the transmitter and the receiver (the LED of the receiver is solid on), connect the transmitter to the
computer, then open the FlyskyAssistant on the computer to update the firmware.
Connect the transmitter to the computer. Then put the receiver to enter the forced update mode by referring to the following
two ways (The LED of the receiver operates in three-flash-one-off manner repeatedly). Afterwards, open the FlyskyAssistant on
the computer to update the firmware.
- Power on the receiver while pressing and holding the BIND button for more than ten seconds, until the LED of the receiver
operates in three-flash-one-off manner repeatedly, then release the BIND button.
- Power on the receiver first, then press and hold the BIND button for more than ten seconds, when the LED of the
receiveroperates in three-flash-one-off manner repeatedly, then release the BIND button.
Package Included:
1 x FS-SRM RC Receiver