Customer Reviews

4.95 out of 5
See all 113 reviews
Write a Review
  • All Reviews (113)
  • Image (21)
  • Video (0)
  • All Star
    • All Star(113)
    • 5 Star(110)
    • 4 Star(2)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
Show Original

A part of the review has been auto-translated.

  • 31/10/2021

    #New 2 the RC world.... The product come 4 days before it's due date to come in the post, I had a hard time finding the right receiver for this RAF S.E.5A as there is not much information on the S.E.5A But I can recommend this receiver in any RC build your planning to do it works really well with the transmitter I have #FlySky, no binding issues, and building this aeroplane right it flys really well with the receiver. Thank You Banggood for this receiver bargain price for quality goods.

    Show Original
  • 13/03/2021

    Thank you for the quick delivery.

    Show Original
  • 03/11/2020

    Product not yet tested. Please note that the battery socket is neither welded nor delivered and the servos sockets are of the JST 1.00mm type. It can be noted that the components of welded surfaces on the plate do not match the photos on the website. I believe this is an updated version and the receiver supports the "AFHDS" and "AFHDS 2A" protocols (see comments and questions).

    Show Original
  • 25/09/2018

    Perfect for the small balsa rc models sold here on Banggood. I have used in LX17, Fokker EIII so far. Flying radio range is great. I am still in control when I can barely see plane in distance.

    Show Original
  • 14/09/2017

    This receiver is nice and very small but comes without documentation. It is very similar to the "2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC" Product ID: 1072251 and the "Mini Futaba SFHSS Compatible 8CH Receiver PPM Output With 1mm JST Socket For DIY Micro Quadcopter" Product ID: 1083120 and you can get some more information by digging into the descriptions of these receivers. It binds with my Turnigy 9X / Flysky TH9X but the process takes some time for the first bind to occur. In PPM mode (with a jumper added on the pcb…) the pulses stream is on the signal output of channel 1 / throttle connector. The others channels are not available on the connectors but the ESC output is still usable. See the picture of the waveforms: upper signal is from channel 1 connector, with the ESC output just below. The receptor does not feature cutoff for lipo protection: I tested that the ESC keeps driving a small motor with an input voltage as low as 2.4v. So be careful if you use a 1S lipo. 1.0mm 3-pin JST connectors are not available at Banggood, nor some tiny compatible servos. Just a pity... It is bit expensive if you compare it to a V911 of F929/939 receiver with 2 integrated servos

    Comments (2)
    Show Original
  • 28/02/2018

    It is a really small and light receiver. The connectors are JST 1.0mm. It has been easily bound with my Flysky FS-i6 transmitter. Some instructions about the connections would be welcomed.

    Comments (5)
    Show Original
  • 18/07/2017

    Some instructions would be helpful, the channels are not labeled, the connector for the lipo should be included and the labeling for the motor and battery are poorly labeled. The receiver starts in bind mode on my Ultimate 7E I select flysky and press bind and it binds. Ultimate 7E is Devo 7E with upgraded arm for more memory. I also heave installed a 3in1 multi module which was cheaper on aliexpress.

    Show Original
  • 12/03/2020

    Super small receiver with integrated controller for brush motors. Very good for small indoor flyers. Only the 1mm JST sockets are not suitable for 1S servos with mainly 1,25mm JST connectors, but there are adapter cables. Works perfectly!

    Comments (2)
    Show Original
  • 01/08/2017

    it's tiny ! - the same size board as "2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC" and shares the same 1mm spaced pins in the servo sockets (compatible with hk-5320s servos), although the chip components are laid out differently size and weight consistent with descriptions way smaller than the wltoys f-series receiver (shown for comparison in the pic) the layout would presumably the same as the dsmx version for the wires - motor connections for the esc marked M on the left of the underside, and battery to the right; both with their positive lead on the middle (pair of) solder pads haven't tried it yet, but the dsmx version worked fine, and i expect this should too

    Show Original
  • 25/11/2018

    This receiver is excellent, I know others have had binding problems with them, I think the software has changed, I use my FS-i6 and AFHDS2A and it binds perfectly, along with telemetry

    Comments (1)
    Show Original

    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • US$28.48
    • US$9.23
    • US$15.16
    • US$15.16
    • US$9.23
    • US$10.91
    • US$25.11
    • US$15.74
    • US$20.78
    • US$19.84
    • US$27.59
    • US$3.99
    • US$5.99
    • US$9.59
    • US$75.99
    • US$51.99
    • US$21.99
    • US$13.39