Precise details:

Battery(Not include)

Description:

Brand:Others

Application:Other,Outdoor

Applicable User:Professional,Universal,Beginner,Intermediate ,Advanced 

Camera Resolution:1000tvl above

RC Drone Spare Parts:FPV Camera,FPV Transmitter

Feature

1. Working channel 5.8G 48CH.
2. Support 2-4S power supply.
3. VTX with 5V/300mA output to camera.
4. 200mW(270mA)/500mW(350mA)/1000mW(430mA)/1600mW(570mA)adjustable.
5. With CMOS 1500TVL FPV Camera.
6. Have radiator and Cooling fan.
7. Strong shock resistance of power supply.
8. Built in DVR module, supports up to 64GB memory card, can record video after power.

Frequency 5.8G 48CH

Button Description Step 1: Press and hold the button until the Red LED flash 1 time which means the item of channel selecting , then press the button can select the channels (Blue LED flashing times corresponds to CH1-CH8). Step 2: 

Press and hold the button again, the Red LED will flash 2 times which means the item of Band selecting , then press the button can select the Band (Blue LED flashing times corresponds to A-R). Step 3: 

Press and hold the button again, theRed LED will flash 3 times which means the item of power level selecting , then press the button can select the power (This step is essential for setting). Finally, press and hold the button to save the parameters. The red and blue lights are always on. Pit mode: 

Press the button twice will toggle the OFF/ ON PitMode. The red light and blue light are flashing, indicate it enter to PitMode, and the working distance is only 1-2 meters.When the red light and blue light are always on,the transmission is in normal work.

Instruction 1. 5V DC: 4.5-5.5V; 2. “-”DVR Grounding wire for power supply; 3. VO DVR Preview and Playback CVBS Video output; 4. AO DVR Preview and Playback Simulated Audio Output; 5. VI DVR video CVBS signal input; 6. AI DVR Simulated audio input for recording. ( lf audio is required, it should be paired with an active silicon microphone to connect to Al and AO. )

Note: A. VO: If an image display device can be connected, it is the CVBS video input end of the image transmission. In this connection method, there is about a 100 ms delay between the video page and the DVR input video. When viewing the DVR working page on the display device, refer to the key panel operation for the corresponding page description. If you have requirements for the delay, please follow connection method B. B. VI: If there are requirements for image delay, connect the image transmission device or the display device and the camera to this port. C. The characteristics and usage of A0 and Al are the same as those of VO and VI.

Status Indicator Light When the DVR module is powered on, if the TF card is properly installed and self-test is normal,the red light will flash to start recording. If the red light does not turn on, follow the self-check sequence below: A. Please check the TF card capacity and installation first to ensure they are correct. B. If the TF card capacity and installation meet the requirements, please check the power supply. C. Enter the DVR preview and initialize the TF card through the button panel operation.

Button Expansion Board: Solder the provided button expansion board to the location shown in Figure 3 above. Solder the red wire to "K" and the black wire to "G". The buttons include a 5-way button with Up (UP)，Down (Down),Left (Left)，Right(Right), and Confirm. This button board can be used for OSD parameter adjustment of the RXCRC 1200-line lens. 

Expansion Board Operation Instructions: 1.DVR Preview Interface: ·From top to bottom on the left side of the screen, the icons are as follows: - Preview video icon. - Single recording file duration (the character unit "minutes" is displayed on the icon). - SD card status (if the SD card is abnormal, a red character will appear on the icon). A. Confirm Key: Start/stop DVR recording. - When recording starts, a red dot will flash in the upper- left corner of the screen, and the module's red light will flash at the same frequency. - When recording stops, the red dot in the upper-left corner disappears, and the module's red light stops flashing. B. Left Key: Enter theDVR playback page. C.Right Key: Enter the DVR parameter settings. Set the corresponding parameters according to the popp-up dialog box. It is recommended to only modify the single recording file duration. Format the TF card if necessary.

2. DVR Playback Interface - The current file name is displayed at the top, and the playback start/stop icon is at the bottom-right corner.

- In playback stop mode, press the up key to switch to theprevious file.
- In playback mode, press the up key to adjust the volume.
C. Down Key:
- In playback stop mode, press the down key to switch to the next file.
- In playback mode, press the down key to adjust the volume.
D. Left Key: Exit playback and enter preview mode.
E. Right Key: Delete a file. Operate according to the popp-up dialog box.

3. DVR Module Power-On.

When the DVR module powers on and enters preview mode, if the video display end is not connected to the VO, do not connect the key panel to avoid blind operations that may affect DVR functionality.

Package Included:

1.6W All-in-One (AIO) 1500TVL 130° FPV Camera & FPV Transmitter