Customer Reviews

4.91 out of 5
See all 76 reviews
Write a Review
  • All Reviews (76)
  • Image (10)
  • Video (0)
  • All Star
    • All Star(76)
    • 5 Star(71)
    • 4 Star(3)
    • 3 Star(2)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
|
Show Original

A part of the review has been auto-translated.

  • 15/01/2020

    Very good board, but has a few downfalls. You can’t turn off the board and charge the battery at the same time. Also hardware Serial 2: GPIO 16 and 17 don’t work while using the OLED, to solve this problem I used jumper wire so the OLED rst is connected to 3V, and cut the trace to GPIO 16. Other than that it’s a very good board for an even greater price!

    Comments
    Show Original
  • 01/03/2018

    This board works great, I was able to get both the WiFi and the OLED up and running. The OLED is a bit tricky, it's not connected to the standard I2C pins, its SDA pin is 4 and SCL pin is 15. You can set this up by adding Wire.begin(4, 15) to your setup code. The display's I2C address is 0x3C. You will also need to use the OLED_RST pin to enable the display: pinMode(16,OUTPUT); digitalWrite(16, LOW); delay(50); digitalWrite(16, HIGH); After applying these settings I2CScan can find the display and most SSD1306 Arduino libraries work (for example the Adafruit SSD1306 works after changing Wire.begin() to Wire.begin(4, 15) and setting the reset pin and the I2C address).

    Comments (6)
    Show Original
  • 15/05/2019

    Works. I've read some overcomplicated about the display. I got it to work with U8g2lib. I used the following constructor line: U8G2_SSD1306_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE, /* clock=*/ 16, /* data=*/ 17); this has to be changed to the right pins so it becomes: U8G2_SSD1306_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ 16, /* clock=*/ 15, /* data=*/ 4); This got it working for me with the usual U8g2lib functions.

    Comments (2)
    Show Original
  • 09/03/2018

    Works great. here is how to get working with arduino IDE: https://github.com/espressif/arduino-esp32#installation-instructions Also, LCD might be a bit tricky install library: "ESP8266 and ESP32 Oled driver for SSD1306 display" Look at my attached pictures for minimum demo.

    Comments
    Show Original
  • 26/04/2019

    Очень быстро доставили(СDEK прямо к дверям квартиры).Очень шикарно упаковано(хоть с десятого этажа бросай).Проверил сразу---все работает.Огромное спасибо продавцу!!!!Все отрицательные отзывы для меня ---бред!Работают круче чем Аli.Наверное спасибо конкурентной борьбе....:):):)

    Comments
    Show Original
  • 16/02/2018

    Very nice little ESP32 board with OLED display, when it came i plugged it to usb and demo program was running but I am not able to get it working now, i tried to do it with information from comments but did not worked for me, also tried to check IC2 address with ic2 scanner but without success, but board works well.

    Comments
    Show Original
  • 29/12/2017

    It looks good at first glance The screw is very close to the antenna, I hope that is not a problem

    Comments
    Show Original
  • 23/04/2018

    Module works good so far. Next is to exercise the complete flash. Thanks to eagle for the message below how to get the OLED operating.

    Comments
    Show Original
  • 22/02/2019

    Happy with this module. Working as it should. Easy to programming with the tips on this site

    Comments
    Show Original
  • JayVIP4
    CA
    10/05/2018

    Very good price and quality

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • £4.62
    • £11.17
    • £10.73
    • £3.83
    • £11.27
    • £8.90
    • £7.34
    • £3.57
    • £3.83
    • £13.69
    • £5.21
    • £3.06
    • £25.31
    • £4.60
    • £4.60
    • £16.10
    • £4.60
    • £19.94