Very good item: stable voltages and clean output (noise-free power source) due to good quality of built-in LC filter (high capacity smd capacitors and good inductors). Very easy to solder, and big solder pads lets to easily un-solder different wires from esc or battery if needed. Powe output pads are also very well placed, so it's very easy to reach it. As I have used this PDB before, I can confirm, that it had survived a lot of copter crashes and still is working very well. LED switch is also very useful, when you don't need the navigation lights to be used, and also - is very easy to switch it on or off.

Very good item: stable voltages and clean output (noise-free power source) due to good quality of built-in LC filter (high capacity smd capacitors and good inductors). Very easy to solder, and big solder pads lets to easily un-solder different wires from esc or battery if needed. Powe output pads are also very well placed, so it's very easy to reach it. As I have used this PDB before, I can confirm, that it had survived a lot of copter crashes and still is working very well. LED switch is also very useful, when you don't need the navigation lights to be used, and also - is very easy to switch it on or off.

Very good item: stable voltages and clean output (noise-free power source) due to good quality of built-in LC filter (high capacity smd capacitors and good inductors). Very easy to solder, and big solder pads lets to easily un-solder different wires from esc or battery if needed. Powe output pads are also very well placed, so it's very easy to reach it. As I have used this PDB before, I can confirm, that it had survived a lot of copter crashes and still is working very well. LED switch is also very useful, when you don't need the navigation lights to be used, and also - is very easy to switch it on or off.

I measured the 5V and 12V output to be 5.008V and 12.03V respectively with a 15V input so that's fine, however, the LED output was the same as the input voltage so be careful about which LED's you attach to the LED output!! Should be ok for 12V LED strip and 3S battery. Also, there is no information on how much current these regulators can supply and the part number of the IC has been removed so I can't check myself... I will be using this board for a 3S tricopter setup, which means that I won't get a regulated 12V output. I will be changing the resistor feedback of the 12V supply to provide 6V for the tail servo. Great for the price.

I measured the 5V and 12V output to be 5.008V and 12.03V respectively with a 15V input so that's fine, however, the LED output was the same as the input voltage so be careful about which LED's you attach to the LED output!! Should be ok for 12V LED strip and 3S battery. Also, there is no information on how much current these regulators can supply and the part number of the IC has been removed so I can't check myself... I will be using this board for a 3S tricopter setup, which means that I won't get a regulated 12V output. I will be changing the resistor feedback of the 12V supply to provide 6V for the tail servo. Great for the price.

I measured the 5V and 12V output to be 5.008V and 12.03V respectively with a 15V input so that's fine, however, the LED output was the same as the input voltage so be careful about which LED's you attach to the LED output!! Should be ok for 12V LED strip and 3S battery. Also, there is no information on how much current these regulators can supply and the part number of the IC has been removed so I can't check myself... I will be using this board for a 3S tricopter setup, which means that I won't get a regulated 12V output. I will be changing the resistor feedback of the 12V supply to provide 6V for the tail servo. Great for the price.

Simple PDB with 5v/12v BEC. Switch is just for on/off LED output that just VCC (input). 5V output is 4.95V starting from 6v input. 12V outpu is 12v starting from 14V input, otherwise unstable and below 12v. The board can be cleaner...

Simple PDB with 5v/12v BEC. Switch is just for on/off LED output that just VCC (input). 5V output is 4.95V starting from 6v input. 12V outpu is 12v starting from 14V input, otherwise unstable and below 12v. The board can be cleaner...

Simple PDB with 5v/12v BEC. Switch is just for on/off LED output that just VCC (input). 5V output is 4.95V starting from 6v input. 12V outpu is 12v starting from 14V input, otherwise unstable and below 12v. The board can be cleaner...

Fonctionne tres bien stable et fournit +12 et +5 volts. Idéal pour faire votre construction de votre propre quad et fournir de l'énergie à vos FC, LEDs et des engins de FPV je recommande bonne qualité bon prix Bangood :)

Fonctionne tres bien stable et fournit +12 et +5 volts. Idéal pour faire votre construction de votre propre quad et fournir de l'énergie à vos FC, LEDs et des engins de FPV je recommande bonne qualité bon prix Bangood :)

Fonctionne tres bien stable et fournit +12 et +5 volts. Idéal pour faire votre construction de votre propre quad et fournir de l'énergie à vos FC, LEDs et des engins de FPV je recommande bonne qualité bon prix Bangood :)

Easy payment. It has everything you need to power FPV CAM and NAZE32

Easy payment. It has everything you need to power FPV CAM and NAZE32

Easy payment. It has everything you need to power FPV CAM and NAZE32

I use this on my Krieger 225 quad as the pcb components are low so there is space above the board for other things so far I have not experienced any brown-outs or other problems.

I use this on my Krieger 225 quad as the pcb components are low so there is space above the board for other things so far I have not experienced any brown-outs or other problems.

I use this on my Krieger 225 quad as the pcb components are low so there is space above the board for other things so far I have not experienced any brown-outs or other problems.

The PDB works and provides pretty stable +12 & +5 volts. Great for making your build clean and supplying power to your FC, LED's and FPV gear. Note: A Step UP / Step down Pololu Regulator is a must for your FPV if running 3S or 4S batteries.

The PDB works and provides pretty stable +12 & +5 volts. Great for making your build clean and supplying power to your FC, LED's and FPV gear. Note: A Step UP / Step down Pololu Regulator is a must for your FPV if running 3S or 4S batteries.

The PDB works and provides pretty stable +12 & +5 volts. Great for making your build clean and supplying power to your FC, LED's and FPV gear. Note: A Step UP / Step down Pololu Regulator is a must for your FPV if running 3S or 4S batteries.

Thank you, goods until it's okay.

terima kasih,barang smpai dalam keadaan baik.....

Thank you, goods until it's okay.

in good condition

in good condition

in good condition

tutto,ok...

tutto,ok...

tutto,ok...