All Messages

mrphyslaw an extra battery can be from 9 to 14$ us. The 969 comes in green or orange. 20$US for a new ori6 set of wheels and tires.

2020-05-22 02:15:50 Helpful (0)
Submit
Answers (1)

Q: can i use this with an Eachine EO10S pro? thanks

Asked by BG221163912 on 2020-04-17 05:06:57

mrphyslaw not without a multiprotocol module

2020-04-28 02:22:57 Helpful (0)
Submit
Answers (1)

Q: does it work with the a959b 1/18?

Asked by isaiahscott904 on 2020-04-27 11:38:18

mrphyslaw no you have to replace esc and servo

2020-04-28 01:18:03 Helpful (0)
Submit
Answers (4)

Q: why now Tyro132 at 14% off lmao

Asked by mrphyslaw on 2020-04-08 12:30:09

Pachy glossal The shipping fare is higher because of COVID-19

2020-04-20 05:03:08 Helpful (0)
Submit
Answers (1)

Q: fly time 19000. ?! fly time 25000 ?! please

Asked by CLosHill on 2019-12-18 10:18:44

mrphyslaw don't forget 48khz jesc:)

2020-04-07 11:43:17 Helpful (0)
Submit
Answers (2)

mrphyslaw flashing esc firmware to jess 48khz and emuflight with mocking bird tune helps a lot cruising lightly with 19k and the original 300mah batt gets me about 4 and half min

2020-04-07 11:41:32 Helpful (1)
Submit
Answers (2)

Q: What does the switch on the charger do?

Asked by BG408071164 on 2020-01-21 09:57:56

mrphyslaw fyi flick switch towards battery connections for 4.2 and towards usb side for 4.35

2020-04-07 11:36:40 Helpful (0)
Submit
Answers (2)

Q: The 1900kv or the 2500kv for an FPV newbie? 🤔

Asked by jjhall on 2020-02-06 05:22:44

mrphyslaw 1900kv is plenty 2500kv eat batteries way faster even with 48khz and emuflight.

2020-04-07 11:33:09 Helpful (1)
Submit
Answers (2)

mrphyslaw not really without heavy modification the fs-i6x doesn't have a Jr bay. There are 3d printer stls online to help and you would have to do some wiring and soldering along with a step down transformer. Even then you wouldn't be able to use the serial function without open tx just the ppm

2020-04-07 11:08:22 Helpful (0)
Submit
Answers (1)

Q: would these work on the eachine trashcan?

Asked by FPVShadow on 2020-04-07 11:52:03

mrphyslaw these have a .8mm hole and are 40mm you need 1mm and 40mm

2020-04-07 11:02:20 Helpful (0)
Submit
Answers (5)

mrphyslaw Actually in order to charge 1s on this type of board with the b6 mini or any other 4 button charger you don't connect the parallel cable at all. You have to modify one of the 3 included adapter cables to connect or jumper any one of the PH2.0(1s) plugs to any one of the xt-30 plugs in center and only connect main power cables. Then In system settings go to Bal. Connection set to 0FF. Now you can charge, fast charge, discharge or storage charge 1s like normal using board. Only five at a time. Do not forget to disconnect jumper and turn bal connection back ON before charging 2 or 3s.

2020-03-13 01:48:06 Helpful (0)
Submit
Answers (1)

Q: Magic sticky tape is velcro?

Asked by lordango on 2020-03-12 09:14:53

mrphyslaw Yes it is almost identical if not better than original pre-cut velcro mounting tape. I also reused existing and will keep for spare.

2020-03-13 01:08:49 Helpful (0)
Submit
Answers (2)

Q: are the shocks on this oil filled?

Asked by fost318 on 2019-06-04 04:21:14

mrphyslaw No the shocks are not oil filled. They just have a screw shaft with no seal they cant be filled like for example wltoys 9x9 series. The length of the shocks are about 67 to 68mm hole to hole center. 70mm shocks would be the easiest to find replacement.

2019-06-27 04:03:32 Helpful (0)
Submit
Answers (3)