FoobarFred
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

FoobarFred 16/04/2018
I bought the red and black props at the same time. The black props have extra thick plastic near the hub of the prop, reducing the likelihood of breakage on a crash. The red one received do not have the extra thick material. I have broken 9 red props right at the hub and only one black one on the same quad. Other than old inventory, it's a great prop and works well on my 165mm 1806 2850KV quad. They are more fragile than a dal indestructible however.
10 Pairs LDARC 4045 4x4.5 2-Blade 4 Inch PC Fiber Glass Propellers CW CCW for RC FPV Racing Drone
US$7.25 US$11.99
1
Recommendations
Comments (0)
FoobarFred 22/08/2018
These standoffs are threaded all the way through so you can cut them down (50 will last me a long time). I use a razor blade with a homemade miter jig to make sure my cuts are straight. Flat to flat measure 6mm and point to point is about 6.8mm.
Suleve™ M3NH12 50Pcs M3 Nylon Hex Hexagonal Female Thread PCB Standoff Spacers 20/25/30/35/40mm
US$5.24 US$10.99
2
Recommendations
Comments (0)
FoobarFred 22/08/2018
One of my bearings was struggling on an EMAX RS2205 motor. This bearing fit perfectly and resolved the issue. Bearing is 8mm OD, 3mm ID, and 4mm in height.
10pcs 693NSK Brushless Motor Bearing kits for 2205/2207/2204/2206 RC Drone FPV Racing
US$13.59 US$19.99
10
Recommendations
Comments (1)
0V Lipo Killer Discharger for Lipo Battery with XT60 & XT30 Plug RC Drone FPV Racing
US$2.99 US$9.99

Q: Voltage range? 1-6s?

Asked by CandymanFPV on 2019-01-03 12:46:01

FoobarFred No, you will smoke the resistors if you go above 4S. Those are 2512 resistor packages, rated at 1/2W each. 1.2W total required for 4S, 1.9W total required for 5S, and 2.7W for 6S. As you can see, they are marginal even for 4S, so discharge them as much as possible with the motors before attaching to this killer.

2019-04-01 01:45:59 Helpful (1)
Submit
Answers (2)
FoobarFred 22/08/2018
18AWG wire in red and black received... looks right, but I have not used it.
1M 8/10/12/14/16/18/20/22/24/26 AWG Silicone Wire SR Wire
US$2.05 US$6.99
0
Recommendations
Comments (0)
FoobarFred 22/08/2018
Arm matches description. Overall length of arm is 150mm and measures 4mm think. Motor hole spacing is symmetrical and appears to support motor screw diameters from 15mm to 20mm.
Martian I II 190mm 230mm 255mm Carbon Fiber 4mm Arm Kit for RC Drone FPV Racing
US$6.45 US$10.99
0
Recommendations
Comments (0)
FoobarFred 22/08/2018
considerable fisheye observed when pitching forward or back about 40 degrees. There is also very little threads available, so when I put it in my camera there was no room for the locking nut at the focus point. Through trial and error I used an o-ring to get the lens to tight at the right spot and the rubber seems to be keeping it in place
1pc/2pcs/4pcs/5pcs/10pcs Mini M8 1/3'' 2.3mm FOV 145 Degree Wide Angle HD IR Blocked FPV Camera Lens
US$6.99 US$10.79
0
Recommendations
Comments (0)
1pc/2pcs/4pcs/5pcs/10pcs Mini M8 1/3'' 2.3mm FOV 145 Degree Wide Angle HD IR Blocked FPV Camera Lens
US$6.99 US$10.79

Q: Does this lens has fisheye?

Asked by VELOCITRI on 2017-12-08 07:02:01

FoobarFred The lens most certainly does have fisheye. Very noticeable when you pitch forward and back. You do not see this with the original 2.3mm Micro Swift 2 lens.

2018-08-21 04:08:22 Helpful (1)
Submit
Answers (2)
HGLRC 5.8G 6dBi 7.5cm 4-Leaf Clover LHCP FPV Antenna MMCX Pigtail Cable For RC Drone
US$5.30 US$6.36

Q: How much does it weigh?

Asked by FoobarFred on 2018-06-06 04:46:07

Connie about 5g

2018-07-06 02:23:16 Helpful (0)
Submit
Answers (1)
FoobarFred 24/04/2018
Screws look great and nuts are snug fitting on screw thread, so they won;t come off with vibration. Nuts are designed to start threading on the screw with the rounded side of the nut facing the screw... acts like a funnel to guide the nut properly on the screw. The box has movable dividers to keep items separated. Unfortunately, the lid on the box is much thinner than the box so it warps and flexes much too easily. When closed, the lid bows up on front left and right side. There is enough gap between the dividers and the bowed lid such that the nuts get mixed up with the screws. I put a rubberband around the box (left to right) to keep the lid from bowing up when transporting so everything stays separated.
160Pcs Metric M3 Black Nylon Phillips Pan Head Screw Nut Assortment Set
US$9.99 US$11.99
0
Recommendations
Comments (0)
FoobarFred 17/04/2018
I bought red and black props at the same time for the same quad. The black props have extra material near the hub to reduce breakage while the red ones did not come with the extra material. (see photo) Consequently I have broken 9 red props and only 1 black prop. While it is obvious from the photo kingkong changed their design, it is equally obvious Banggood still has inventory of the old design and are knowingly shipping the inferior design to their customers. When I noticed the trend of red prop breakage, 4 months later due to winter weather here, Banggood cites their THREE DAY WARRANTY period and refuses to replace the old design props. When you received your props... make sure they have the added material near the hub.... if not, you have three days to get them replaced. :(
10 Pairs LDARC 4045 4x4.5 2-Blade 4 Inch PC Fiber Glass Propellers CW CCW for RC FPV Racing Drone
US$7.25 US$11.99
0
Recommendations
Comments (1)
TS5828S Micro VTX 5.8G 600mW 48CH Mini FPV Transmitter SMA RP-SMA for RC Drone
US$8.62 US$12.64

Q: How many amps can the 5V output supply?

Asked by FoobarFred on 2018-04-04 07:05:30

Anorchous about 100mA

2018-04-27 02:26:46 Helpful (0)
Submit
Answers (1)
Martian I II 190mm 230mm 255mm Carbon Fiber 4mm Arm Kit for RC Drone FPV Racing
US$6.45 US$10.99

Q: What are the motor mount hole pattern dimensions? They are slotted holes, so what range of hole diameters will it accept?

Asked by FoobarFred on 2017-11-16 05:04:51

Jeane 1806 2204 2205 2206 motor can be compatibled.

2017-12-13 12:01:04 Helpful (0)
Submit
Answers (1)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe