All Messages

Q: does it only measure to 80A or will it blow if i go over 80A?

Asked by rkikuchi2 on 2019-09-21 06:52:23

matu no it wont blow

2022-06-25 08:10:12 Helpful (0)
Submit
Answers (1)
matu 07/04/2020
This is my first fpv goggles. I owned ev800 before, it's helmet. Disadvantages: 1) stock firmware latency is a total disaster. It's about 100-200ms. At first time i crashed a lot in my apartment because of it. Ev800 latency is good. Latest firmware fixed this issue, latency between me previous ev800 and this is about the same. 2) lens quality is poor: there is a dark spot in the middle of the image on each eye because of lens structure. Lens closest to the eye is concave and convex at the same time on one side (closer to eye). It is not notable during the flight. Notable when screen is black. Not whole image is in focus (center is sharp and edges/periphery is blurry or vice versa). It is impossible to set all image sharp. 3) stock quadversity recievers is really hot, it's image quality is satisfying. It drains battery really fast. I have uninstalled both recievers and swapped it with eachine pro58 (prix firmware). This reciever gives better image quality and also it's cooler. But it can't be controlled with goggles (you have to choose frequency on the reciever menu). 4) It is noisy. There is 2 coolers in this goggles, and one of them is always on (its cooling down the internals of googles). It is barely noticable when you fly outside. But annoying during simulation sessions. 5) to find the right position on the face you have to play with sponges and pads a lot, you'd better own a 3d printer to fit goggles well to the face. Advantages: 1) In spite of poor lens quality (you can set up satisfying lens position when it is not so noticable) image quality is great (comparing with ev800). Branches and wires are really noticable during the flight, even dust in air is noticable! When I flew under my bad first time in this goggles I was shocked to see the dust in the air. I am using foxeer montser micro camera + eachine txc23 vtx + speedy bee 2db antenna. 2) it is compact as goggles is. 3) 18650 battery bay has charger and battery indicator. 4) zipper case is useful.
5
Recommendations
Comments (1)
matu 03/02/2021
Пришла вторая ревизия платы. Изменения: логическая часть перенесена на отдельную экранированную плату, в цепь включены компораторы lm239t. Производителя драйверов изменили на неизвестного, если ранее ставились fortior fd6288q, то теперь используются zg6288q, видимо то же самое но от другого производителя. Но неприятный сюрприз ожидал меня возле датчика тока ina139 после вывода out данной микросхемы должен стоять фильтр состоящий из резистора и конденсатора, но есть следы того, что этот конденсатор был установлен на плату и потом по какой-то причине снят. В прошлой ревизии платы, на сколько могу судить по фото, он не использовался (только резистор). На holybro tekko32 же есть и конденсатор и резистор этой цепи (картинка прилагается). И производитель микросхемы ina139 так же требует установки в выходном фильтре резистора и конденсатора. В остальном пайка на высоком уровне, все ровно, и хорошо вымыто. На плате отсутствует какая-либо информация о том какой вывод за что отвечает в колодке подключения к полетнику. Документация в комплекте отсутствует, на сайте производителя так же отсутствует какая-либо документация по этой ревизии регулятора. Распиновка отзвонилась такая же как и на первой ревизии: gnd, vbat, crt, tele, motors1-4. По вопросу отсутствующего компонента был создан тикет, банггуд его закрыл с таким комментарием: не относится к технической проблеме, уже передана нашему профессиональному коллеге для отслеживания. В рамках тикета я не получил ответа нормально ли это для этого регулятора. Учитывая мои знания я понимаю, что проблемы могут быть только с датчиком тока, но эта проблема на регуляторе может вызвать проблему с соответствующим каналом на полетели контроллере. На всех регуляторах 4в1 что у меня есть на датчике тока на выходе присутствует фильтр как описано в документации к микросхеме, т.е присутствуют и конденсатор, и резистор. Будьте внимательны!!!
0
Recommendations
Comments (1)