All Messages

Q: There are 2 usb-c port in the back.. where to connect?

Asked by jvp4ant on 2022-05-26 03:17:33

Bricola Hello, I know, I've got the same question for myself, the installation paper was only half and cut ... After looking on the Internet, I found a video and some other infos. In fact, you have to connect the USB-C cable to the USB-C socket on the edge of the board, not the one in the middle (even thought there is not enough place for the connector). Install the software, connect the unit, install the driver (if needed), select a Theme and RUN. That's it.

2022-05-27 11:32:17 Helpful (0)
Submit
Answers (0)

Bricola@MarcusStein Googlefor "3.5 Inch IPS TYPE-C Secondary Screen" or/and "How to get a cheap Sensor panel for your gaming PC mod" videos. It's only exemples, existing many others. Look at : drive_google_com \ drive \ folders \ 1H3L3C2pDzqeQ3fPw8nPMSdD9iJpZ1f4w change _ to . and \ to normal slash

Skaravaios 27/04/2022
5
Comments (3)

Q: Is there a place to find more themes than the already installed?

Asked by Skaravaios on 2022-04-27 05:26:44

Bricola I do not know, but you can create your own theme. There is a video you can watch on YTB : "_kRdJ65wO0o" that have a part which gives you tips how to do your own theme. Note that the size of images has to be 320x480 for portrait and 480x320 for landscape, has to be png. With the Theme Editor, you can load an existing theme (config directory) and change how you like. UI-Image is the back. By the way, there is a possibility to use (run) the software on other OS, like Linux, MAcOS or other operating systems that support Python 3.x . It existing a "Turing Smart Screen Python project hosted on Github. Take a look at cnx-software com : turing - smart - screen - a - low - cost - 3 - 5 - inch - usb - type - c - information - display , remove spaces before and after -.

2022-05-26 03:56:37 Helpful (0)
Submit
Answers (0)

Bricola At the moment it does not work on mine too. Maybe a bug. Hope this can be fixed by future update.

2022-05-26 01:58:02 Helpful (0)
Submit
Answers (1)

Bricola To enable the "auto start" function : select the Normal Setting and the tick the Auto Start, then Save. It asks then to restart your computer.

2022-05-26 01:54:27 Helpful (0)
Submit
Answers (1)

Bricola wujiahui : No, this LED module does have polarity ! You may look for datasheets like, for exemple RWL-R1025BB or YSLB-10251B5-10. The positive is on the side where the type is written on.

2022-05-23 08:46:08 Helpful (0)
Submit
Answers (3)

Q: do you have a diagram and a parts placement drawing?

Asked by pa5cw on 2019-02-08 01:28:40

Bricola Hi, schematic can be found, Googgle for HTB1Zt0gRXXXXXcSXVXXq6xXFXXXv.jpg You may watch ' MiddvwiHgI0 ' video on YTB that gives lot of explanations. Hope this can help.

2022-05-23 08:25:14 Helpful (0)
Submit
Answers (3)

Q: what are the values of SMD resistors

Asked by BG181145725 on 2020-01-27 10:19:56

Bricola The little SMD resistor is 3Kohms. You will get 2 of them, so one to solder and one as a spare part if you lost or damage it.

2022-05-23 08:07:20 Helpful (0)
Submit
Answers (1)

Bricola Hello,this module is equal to the W3230. I found a Chineese - English manual : that tells P6 = Hight-temperature Alarm (-55°C to 120°C Factory is 120°C) , P7= Data Lock (On-Off Factory is OFF) , P8 = Factory Reset (On-Off Factory is OFF). Hope this help.

Sanyee73 03/11/2021
3
Comments (5)

Q: هل تعمل مع 12فولط 23امبير

Asked by BG101714141 on 2021-11-10 08:29:05

Bricola Hello, if you mean to power the input of the RD6018, it will work (input range power supply 6 to 70V) but the output is going to be under 12V (it is a step down module) and max current is 18A. It is recommended to use the suggested power supply 60V 1080W to have the right efficient PSU.

2022-02-20 03:12:32 Helpful (0)
Submit
Answers (2)

Bricola Hello, regarding the specs , the DC power input range is 6 to 70V, so 68V is ok. The 1000W is ok too, with an efficency of 95% (only exemple) the max power output is going to be about 950W .

2022-02-20 03:02:23 Helpful (1)
Submit
Answers (1)

Bricola Hi, schematic can be found, Googgle for HTB1Zt0gRXXXXXcSXVXXq6xXFXXXv.jpg . Only one of the two SMD resistor is needed, the other one is a spare part. This resistor has to be placed on the plate just under the version of the board ( by exemple V5.0). The other plates are for ' switch ' functions. Please note for the LED display, the common is positive and located at the written type. You may watch ' MiddvwiHgI0 ' video on YTB that gives lot of explanations. Hope this can help.

2022-02-19 05:19:06 Helpful (1)
Submit
Answers (4)

Bricola Micro USB is required. It is on Page 6 of the Instruction Manual (click on the "RD6018(W) operation instructon: Click here to open" to get the Manual).

2022-02-17 02:45:58 Helpful (1)
Submit
Answers (2)

Q: whats excellway?

Asked by BG203611341 on 2022-01-11 01:15:25

Bricola Excellway is the brand name. Do not understand your question.

2022-01-11 03:14:14 Helpful (1)
Submit
Answers (6)