gshingles
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

gshingles 24/11/2020
Pretty good. Not very much gain with the included USB adaptor and cable, but sounds good powered by phantom power on a mixer. The arm is a bit "how ya doin" but adequate for the job.
BM800 Pro Condenser Microphone Kit Studio Suspension Boom Scissor Arm Stand with Fliter
US$36.90 US$47.05
0
Recommendations
Comments (0)
gshingles 18/04/2019
Used on the Anet A6 which comes with a 40mm throat. This made the nozzle a few mm too high even with the build plate fully up, but a careful bend down of the z-switch lever arm fixed that. It puts the cooling duct outlet closer to the nozzle, but that hasn't caused any issues so far. Have used the 35mm throat without any problem since I replaced the broken 40mm one.
5Pcs 1.75mm M6 35MM Nozzle Throat For 3D Printer Extruder RepRap
US$12.99 US$15.99
1
Recommendations
Comments (0)

gshingles They are meant to be about the same thing, but OU2 is buffered through an op amp. Found this vid with reasonably good demo of the board: https://youtu.be/alAly-oTha0

jacquev6 11/11/2017
Attached pictures show poor soldering job on the 50A leads of the sensor. Passing 50A in these joints would melt them. After re-soldering, everything works as expected. Good product overall.
CJMCU-758 ACS758LCB-050B-PFF-T Linear Current Sensor Hall Current Module
US$7.93 US$14.99
5
Comments (2)
2.4-10.5GHz UWB Directional High Gain Wideband TEM Antenna 2.4G Transmission Antenna
US$10.49 US$17.99

Q: Do you have an antenna plot? Radiation pattern at say 2.4 and 5 GHz?

Asked by gshingles on 2019-06-07 07:30:12

Numen it can work with 2.4-10.5GHz

2019-06-11 10:18:54 Helpful (0)
Submit
Answers (1)
gshingles 11/03/2019
Haven't tested the xtal function, but tested the 1kHz against my DSO150 signal generator ok. Assembly is not tricky. I left the paper on the acrylic and carefully cut out a window for the display, will see how long that lasts.
Geekcreit® DIY Frequency Tester 1Hz-50MHz Crystal Counter Meter With Housing Kit
US$9.23 US$12.99
0
Recommendations
Comments (0)
gshingles 02/05/2019
Works as expected.
Excellway® 10/20/30/40/50A 12V 24V Auto Solar Panel Solar Charge Controller Battery Charge Adapter LCD USB
US$13.64 US$15.99
0
Recommendations
Comments (0)
gshingles 01/03/2019
Lead insertion works fine on this one. Letters and numbers all match on each side. Well made.
Prototype Board 400 Hole Breadboard + 65pcs Breadboard Jump Cable
US$5.66 US$5.99
0
Recommendations
Comments (0)
gshingles 01/03/2019
Downloading the image in the description to get immediate satisfaction. Haven't tried the case, the screen fit over the stacked acrylic design I bought locally.
Geekcreit® 3.5 inch TFT LCD Touch Screen + Protective Case + Heatsink+ Touch Pen Kit For Raspberry Pi 3/2/Model
US$16.19 US$25.99
0
Recommendations
Comments (0)
gshingles 01/03/2019
Good shave and fits my razor.
GFLV® 4pcs 5 Layers Blades Shaving Razor Shaver Heads Replacement for Gillette
US$4.99 US$19.90
0
Recommendations
Comments (0)
gshingles 06/01/2019
Works as advertised, if you give it enough juice! I thought mine was broken, brief temp drop then reboot loop with around 1.5A. The quick temperature reading drop appears to be normal though, more amps sorted out the reboot >3A Not a fan of the included conical tip, prefer chisel but it does the job.
Digital LCD Prgramable Solder Iron Station Built-in Acceleration Sensors with STM32 Chip Embedded Interface DC 5525
US$55.61 US$69.56
0
Recommendations
Comments (0)
gshingles 27/06/2018
They seem to do what they claim to. The temperature measurement moves slowly but I don't think that's too much of a problem.
DC 000 Digital Thermometer Hygrometer Weather Station Alarm Clock Colorful LCD Calendar
US$10.91 US$16.99
0
Recommendations
Comments (0)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe