AresFPV
Q: What is the exact diameter of the motor/spindle shaft?
Asked by o0AKB0o on 2020-10-13 04:32:34
AresFPV 8mm
2024-06-16 10:29:02 Helpful (0)
AresFPV will need to solder wires direct to board, or solder pin headers in to use with connectors
2024-06-16 10:28:56 Helpful (0)Q: how do you connect 2 motors for a tank with this?
Asked by highwayman on 2023-12-12 10:53:17
AresFPV you will need 2 escs for 2 different motors. pretty sure this only has one motor output
2024-06-16 10:27:55 Helpful (0)Q: does this Rx work with low voltage servo? If the input vikty is 1S lipo (3.7v-4.2v)
Asked by KLKOK on 2018-09-12 01:18:40
AresFPV yes should work fine but as you said it will need a power input
2023-01-07 02:10:04 Helpful (0)Q: Is this DSMX/DSM2 compatible?
Asked by gjadam1 on 2021-05-02 02:24:15
AresFPV no it is not. it uses the afhds 2a protocol
2023-01-07 02:09:24 Helpful (0)Q: can this be used in EU (italy) ?
Asked by Yexel on 2018-01-04 06:58:52
AresFPV should be ok as its a 2.4ghz system
2023-01-07 02:06:36 Helpful (0)Q: what is working distance between receiver and remote control
Asked by BG539185151 on 2021-11-18 02:20:28
AresFPV average around 400m maximum I expect
2022-11-05 11:46:34 Helpful (0)Q: Can this be used in the uk? The nominal voltage here is 230v
Asked by BG564816174 on 2020-04-17 07:09:06
AresFPV yes the power supply is configured for 230v
2022-11-05 11:45:28 Helpful (1)Q: can it get stuck at customs in India???
Asked by Chaitany on 2020-04-08 12:31:00
AresFPV not sure. may be best to contact BG directly
2022-07-22 04:19:28 Helpful (0)Q: Can I use the bn-880 with that mount?
Asked by M0CKY on 2020-06-22 09:08:43
AresFPV I think the 880 is a bit too large, the antenna would not fit with the lip around the mount. it may be possible for it to fit with slight modification to the mount, but this gps module is just slightly larger
2022-07-22 04:18:45 Helpful (0)
AresFPV you need to print a replacement z carriage, have a look at this one on thingiverse: thing:4803721
2022-07-05 04:17:49 Helpful (0)Q: i have bond with my flysky fs i6 but the Signal com not i don't know why can you please help me
Asked by Mojaa on 2018-10-27 03:31:41
AresFPV it could be you have selected the wrong communication method, this should be pwm for this receiver, that or it did not bind correctly. having a correct binding should show the voltage of the receiver on the transmitters screen
2022-07-05 04:14:29 Helpful (0)Q: does this have a receiver built into it?
Asked by Kevin on 2019-10-18 10:51:54
AresFPV no you will need one separately
2022-06-22 03:00:40 Helpful (0)
AresFPV yes. i suggest using single flute endmill for ali
2022-06-22 03:00:05 Helpful (0)Q: Can this Rx FS2A be binded with a Turnigy 9X V2 AFDHS2A ?
Asked by claudycharlier on 2020-12-05 10:03:08
AresFPV yes the 9xv2 with the afhds2a module will bind as the protocols are the same
2022-05-29 11:26:50 Helpful (0)Q: Is there a wiring diagram available?
Asked by kechols_jr on 2020-04-22 03:19:04
AresFPV fairly simple to wire, power is positive to the fused side i believe, motor doesnt matter as the wires can easily be swapped if the motor spins the wrong way. switch is used to turn on or off the motor separately or through a control board.
2022-05-29 11:13:47 Helpful (0)Q: How do I power up the unit? It is DC right? Difficult to find a DC power converter with 30 Volts
Asked by flowin_through on 2021-04-07 10:14:27
AresFPV the power supply is connected to mains AC. there is no earth connection, but you can add one to the motor and or the power supply for safety
2022-05-29 11:11:03 Helpful (0)
AresFPV may be best contacting BG
2022-05-20 01:46:39 Helpful (0)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
AresFPV the heater only runs off 12v. with the correct AC transformer wire, it would be able to run 110v. uk plug is a 240v to 12v transformer. you would need a 110v to 12v transfer with the correct plug at the heater end
2024-11-22 12:03:25 Helpful (0)