Customer Reviews

4.9 out of 5
See all 3040 reviews
Write a Review
  • All Reviews (3040)
  • Image (353)
  • Video (3)
  • All Star
    • All Star(3040)
    • 5 Star(2836)
    • 4 Star(148)
    • 3 Star(28)
    • 2 Star(11)
    • 1 Star(17)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
Show Original

A part of the review has been auto-translated.

  • 04/02/2016

    The cable provided is compatible with my Flysky i6 Tx for simulation on FPV Freerider

    Comments (1)
    Show Original
  • 06/01/2017

    As others have said, this works great with the I6. To get this working correctly, I set the toggle on the dongle to "G5-G7 Above", plugged the cable into the port on the backside of the TX, and set the TX to "Student Mode". Make sure to check your control panel's "devices and printers" section to see if a gaming controller is present. To set your I6 in student mode, turn the power switch off and hold the two bottom trim buttons inward, and then proceed to toggle the power on. After it has powered on, release the trim buttons and hold the "OK" button to access the menu. The rest should be straight forward. Note that I have not been able to get the TX to be recognized with the I6 programmer to flash the firmware. If anyone has any luck with that, please comment.

    Comments (1)
    Show Original
  • 09/12/2016

    USB dongle works witch Eachine i6 (From RTF kit Falcon 250 Pro). By default Eachine i6 doesn not send PPM signal on "trainter" connector on the back, so every time when you want to use simulator you need set in transmitter menu an option "Student mode". On this USB cable set second option "G5-G7 Above". It work for me with Freerider on Android an on Mac Os X without any additional drivers.

    Comments (3)
    Show Original
  • 24/11/2014

    All the supplied software works with the simulator cable. RealFlifht G7 PhoenixRC X5 Aerofly Reflex XTR and VRC Installed everything without any problem. Only one issue - the sticker says about 5 positions of the switch, but actually there are 4 (the 5th position is VCR2). But nevertheless it is the best value of money! Highly reccomend

    Show Original
  • 27/01/2019

    ben cok begendim tam flyskya uygun cd nin icinde uygulamalarda var. kargo 8 gundr ulasti saka gibi :) cinden mi aliyoz yurt icinden mi belli degil

    Comments (2)
    Show Original
  • 19/04/2016

    I got this to practice with simulators before flying the 250 I built. It took a few tries to get things working but no complaints. I'm running Windows 10. Some things to note; Pick an unused model on the transmitter and enable trainer mode. Plug in USB. Make sure your transmitter shows up in devices before launching the sim program. Calibrate. Enjoy!

    Comments (1)
    Show Original
  • 08/09/2021

    He's infected my computer with a virus that brings the simulator and now there's no way to remove it. Pay with PayPal, I will claim the amount of the simulator and the damages caused to my laptop.

    Show Original
  • 15/07/2020

    Very fast in delivery to Chile the package arrived very well the products are exactly as they indicate in their photographs ,working without problems with Flysky Transmitter FS-i6X i6X 10CH

    Show Original
  • 21/04/2020

    order arrived in 10 days via ninjavan to singapore despite covid delay. works well with phoenixRC on windows 10- plug and play, no driver installation needed to use the USB dongle. included CD comes with a whole suite of software, and I used that to install phoenixRC 5.0.b no issues using with my turnigy 9XR. tried both the JR and futaba ports on my tx and they work flawlessly. however, calibrating the controls on phoenixRC was quite tricky...i had to make sure all sticks(including throttle) were centred before entering the calibration page otherwise my throttle channel will register 100% input whenever the sticks are beyond 50%. overall very satisfied!

    Comments (4)
    Show Original
  • 25/03/2017

    This simulator cable works great with a FlySky FS-I6x and FPV Freerider on Arch Linux. Just set switch to position 2 "G5-G7 Above", attached transmitter cable, turned on transmitter, cenetered sticks, plugged into USB port and started FPV Freerider. Cable lenght is perfect. It will quickly pay for it's in saved props. Just buy it. :) I'm happy I did.

    Comments (1)
    Show Original

    Total 0 pages

    Go to page


    You might be interested in

    recommendation for you
    • US$43.99
    • US$51.44
    • US$5.00
    • US$11.54
    • US$85.99
    • US$95.99
    • US$6.29
    • US$6.32
    • US$55.99
    • US$26.99
    • US$71.99
    • US$9.44
    • US$10.49
    • US$14.69
    • US$10.49
    • US$37.79
    • US$8.49
    • US$346.49