Customer Reviews

4.84 out of 5
See all 244 reviews
Write a Review
  • All Reviews (244)
  • Image (65)
  • Video (1)
  • All Star
    • All Star(244)
    • 5 Star(214)
    • 4 Star(24)
    • 3 Star(5)
    • 2 Star(0)
    • 1 Star(1)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
|
Show Original

A part of the review has been auto-translated.

  • 09/08/2020

    Shipping took 3 work-days and the printer came partly assembled and nicely packaged. The printer has a steel sheet-metal frame with some magenta-metallic aluminum parts and some 2020/2040 aluminum V-Slot profiles. Stiff coupler for the z-Motor and ferrules! The frame is reasonable stiff for a printer and the assembly was easy thanks to the great pdf-manual on a SD-Card and the video on the Biqu-youtubechannel. Every bag of screws is labeled and you also get some spares as well as any tool or wrench you need. The Cablemanagement is great and you are supplied with enough cableties. The type-C cable makes maintanance on the hotend easy and you dont have to deal with multiple cables at all. My bowden was a little short and was bending a bit much, 5cm longer would solve this. The hotend is a grub screw clamped V6 hotend 0.4mm nozzle and two spares. The heatbed is a 3mm aluminum-PCB with a magnetic pad and a springsteelsheet. It works very well and heats up to 250°/80° in 5-7 min. Unfortunately my bed is not flat, so at some point I will have to buy a BL-Touch for autoleveling to compensate that. The TMC-Driver make this printer as silent as a Prusa but this is mitigated by the case and driver-cooling fans which are as loud(48dB@1m) as a hairdryer on lowest level. You cant tell if the printer is running or not! These must be replaced if you consider printing in a livingroom. Touchscreen is bright, responsive and has many configuration options. I also had to adjust the steps-per-mm-value of x and y from 81.5 to 80.00 to get my parts to nearly the correct size. I dont understand why they choose these values in the first place since 80.00 is the calculated standard value for this assembly. The printquality is very good and bed adhesion is fantastic. All in all this printer is a very good deal, but it has some flaws which should be fixed or adressed. Its maybe not the best for a total beginner, but with a little bit of finetuning you could turn this into a great printer.

    Comments (1)
    Show Original
  • 29/07/2021

    Five stars! Sensational! It is easy to assemble and the manual is very explanatory, hardly need to read. The pieces are all numbered and the tools are coming up to assemble. In a matter of software, the firmware installed in it is very good. It's practically assemble and leave printing. Of course, for a beginner it requires some study but I was able to print my favorite piece as soon as I finished putting it together. Really sensational! A differential is the led illuminating the print bed. Only one detail I missed was the memory card that didn't come to me. I am very pleased also with Banggood's fare insurance. I was redeemed with the full value of the customs fee and it was very quick. I was very well attended by the staff. Congratulations!

    Comments (2)
    Show Original
  • 19/07/2020

    OK the printer isnt all bad but in its current state is certainly not for first time buyers. So far I have replaced a pulley that squeaked because it was rubbing against a metal spacer, the USB port does not line up with the whole in the case so cannot use until i widen the hole. It has no bed wire strain relief which we had to find and adapt to this printer as it is vital. This is all in a single day, we fix an issue and find another. Most of these are pretty minor but no one buys a printer to have to fix its issues. I think a selection should have been sent out to enthusiasts to test and give feedback, ive seen a single review and that was after its release. On the flip side there is a lot i do love about this printer, the colour is funky, the extruder is metal, the touchscreen and software seems sound and it has potential. I just dont think its quite there on the testing and tweaking part before it should have been released.

    Comments (1)
    Show Original
  • 08/07/2021

    It came well packaged, but it didn't come with the SD card unfortunately, it comes with 50 grams of PLA that you can play with a little, easy assembly, and it already prints with very good quality from the box, I didn't have to do anything other than the table alignment to get the prints on top quality. Would recommend for beginners.

    Comments (6)
    Show Original
  • 03/02/2021

    nice 3d printer . good quality . dont expect to make job with the 50 gr of filament that the printer include . i assembled it with the help of a video in you tube . i recomend it. good print quality

    Comments
    Show Original
  • 08/08/2020

    I own many 3d printer but for sure this is the best one . high quality materials. biqu have put a lot of effort on this product. I recommend 100% . biqu have the best customer service. great results with pla and petg . going to order another soon for my farm

    Comments
    Show Original
  • 15/07/2020

    Delivery within 48 hours 👍😍 printer runs very well and the display with software is fantastic. very many settings possible. Is not my first printer but the printer is worth the money for this price with 32 bit board. would buy this again and again.

    Comments (3)
    Show Original
  • 06/09/2021

    Really good printer for the price and arrived on estimated delivery date. Was charged tax and clearance fees in my country but since i had tarrif insurance, banggood refunded me 100%. 5 stars for the product and the service. Only downside was that my printer got damaged while it was shipped, thats Amarex's fault, but printer still works 100%

    Comments
    Show Original
  • 18/07/2021

    I don't have the words to describe that printer. I'm simply enchanted by her. It was a sure and very happy choice. I strongly recommend purchasing this printer!!!

    Comments (2)
    Show Original
  • 03/01/2021

    super well packed, a lot of good quality foam, the printer is very easy to mount and quality of the box is good, after some upgrades is now almost perfect

    Comments (2)
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • US$4.99
    • US$34.99
    • US$5.99
    • US$249.00
    • US$3.99
    • US$399.00
    • US$64.99
    • US$29.99
    • US$17.99
    • US$428.00