This works well and I highly recommend this to get your plane quickly into the air without a flight controller. It automatically recognizes the protocol, in my case inverted sBus from an XM+ set to 16CH with telemetry on channel 16 (FCC firmware). However, the converter was factory set to channels 9-16 rather than channels 1-8. I read all the instructions, reviews, and answered questions and nobody says how to fix this. Firstly, the red light you might think is a power light is actually telling you it's set to channel 9-16. Secondly you can't just push the button to switch it as the instructions say. You must power up with the button pushed, as if you were binding. The cool thing is you could have two of these, connected to the same sBUS output, controlling 16 servos. Or you can send sBus to the flight controller and this unit getting channels 9-16 from this device for gimbals and such. What an amazing converter!

This works well and I highly recommend this to get your plane quickly into the air without a flight controller. It automatically recognizes the protocol, in my case inverted sBus from an XM+ set to 16CH with telemetry on channel 16 (FCC firmware). However, the converter was factory set to channels 9-16 rather than channels 1-8. I read all the instructions, reviews, and answered questions and nobody says how to fix this. Firstly, the red light you might think is a power light is actually telling you it's set to channel 9-16. Secondly you can't just push the button to switch it as the instructions say. You must power up with the button pushed, as if you were binding. The cool thing is you could have two of these, connected to the same sBUS output, controlling 16 servos. Or you can send sBus to the flight controller and this unit getting channels 9-16 from this device for gimbals and such. What an amazing converter!

This works well and I highly recommend this to get your plane quickly into the air without a flight controller. It automatically recognizes the protocol, in my case inverted sBus from an XM+ set to 16CH with telemetry on channel 16 (FCC firmware). However, the converter was factory set to channels 9-16 rather than channels 1-8. I read all the instructions, reviews, and answered questions and nobody says how to fix this. Firstly, the red light you might think is a power light is actually telling you it's set to channel 9-16. Secondly you can't just push the button to switch it as the instructions say. You must power up with the button pushed, as if you were binding. The cool thing is you could have two of these, connected to the same sBUS output, controlling 16 servos. Or you can send sBus to the flight controller and this unit getting channels 9-16 from this device for gimbals and such. What an amazing converter!

works as described.

werkt zoals beschreven.

works as described.

получил, вроде нормально все с ним. В работе не проверял

получил, вроде нормально все с ним. В работе не проверял

получил, вроде нормально все с ним. В работе не проверял

entrano senza problemi anche nelle fusoliere più strette

entrano senza problemi anche nelle fusoliere più strette

entrano senza problemi anche nelle fusoliere più strette

"Распаковщик" SBUS сигнала. позволяет получить с комплексного SBUS сигнала с 1 по 8, или 8 по 16 PWM каналы.

"Распаковщик" SBUS сигнала. позволяет получить с комплексного SBUS сигнала с 1 по 8, или 8 по 16 PWM каналы.

"Распаковщик" SBUS сигнала. позволяет получить с комплексного SBUS сигнала с 1 по 8, или 8 по 16 PWM каналы.

So far I have only tested this item in my workshop and it seems to work fine. The instructions were not good and I did have problems initially sorting out which channels were in use. It came with channels 8-16 set, it pressing the button while connected did not change to channels 1-8. The button must be held in while connecting the power, a bit like binding. Once I had realise that all was well with my testing. I will be ordering more before too long.

So far I have only tested this item in my workshop and it seems to work fine. The instructions were not good and I did have problems initially sorting out which channels were in use. It came with channels 8-16 set, it pressing the button while connected did not change to channels 1-8. The button must be held in while connecting the power, a bit like binding. Once I had realise that all was well with my testing. I will be ordering more before too long.

So far I have only tested this item in my workshop and it seems to work fine. The instructions were not good and I did have problems initially sorting out which channels were in use. It came with channels 8-16 set, it pressing the button while connected did not change to channels 1-8. The button must be held in while connecting the power, a bit like binding. Once I had realise that all was well with my testing. I will be ordering more before too long.

Good value, very pleased with the item. Received it at 9 days

Good value, very pleased with the item. Received it at 9 days

Good value, very pleased with the item. Received it at 9 days

Im Very happy!! i have more Channels for my fpv plane

Im Very happy!! i have more Channels for my fpv plane

Im Very happy!! i have more Channels for my fpv plane

Werde es mal testen

Werde es mal testen

Werde es mal testen

Very useful when you want to make your servos work a PPM or Sbus receiver. Good price good quality. I have been using it for months without a problem. Overall very happy.

Very useful when you want to make your servos work a PPM or Sbus receiver. Good price good quality. I have been using it for months without a problem. Overall very happy.

Very useful when you want to make your servos work a PPM or Sbus receiver. Good price good quality. I have been using it for months without a problem. Overall very happy.