lexx007
Q: Would Binary fly with Sunnysky X*****kv motors?
Asked by giliardi on 2020-06-12 08:46:17
lexx007 Howare you finding the paint holding up after a few flights? I painted mine miltary green but sadly after about 20 flights its losing colour in some areas. Maybe i should laminate it next time, but its such a light plane it seems a shame to add weight.
lexx007 Nicemod looks good on it. I went with 2208 1900kv motors and like yours just takes off almost instantly. Have you noticed any problems with elevator on yours i find one side seems to move more than other side. Have been thinking of just making one big one and trimming the rear of plane to make clearance.
Q: yes please send to eu warehouse
Asked by lexx007 on 2018-08-26 12:46:23
djusco Yes, we want this in EU warehouse!
2018-09-22 03:20:07 Helpful (2)Q: You cannot use the same screws twice as they have a glue on them that is no good the second time
Asked by Seamus Mckenna on 2019-12-15 04:18:45
lexx007 it is called threadlock you can buy some cheaply to reuse screws
2020-05-20 08:45:25 Helpful (1)Q: Do i need this for the Crazybee F3 FC? Like the Mobula 7(NON HD)?
Asked by SeaGuardiian on 2019-06-11 05:49:07
lexx007 No as the original mobula 7 did not suffer from the same power spike problem on 2s as the f4 version did.
2019-10-10 09:52:36 Helpful (0)Q: Do these have a lower stick tension then the original X-lite (non pro) ?
Asked by desjaak on 2019-10-03 09:18:58
lexx007 should be the same, but tension is adjustable via screw on back anyway
2019-10-10 08:14:05 Helpful (0)
lexx007 Yes thats right it will. I personally rolled back the firmware and bootloader of my x-lite to switch to the FCC firmwares and mine will bind in this without the module ( 2 mobula 7 and mobula7 HD bound without module and no problems)
2019-10-10 03:39:55 Helpful (1)Q: How many amps is the BEC rated for?
Asked by MBJ123 on 2018-05-10 06:57:51
lexx007 The bec is 3 amps continuous. enough for a fc and the twin servos used on an f1 or ar wing
2019-02-22 09:37:27 Helpful (1)Q: can i cut 4mm mdf this laser ?
Asked by UgurSirinTR on 2017-11-28 07:23:39
lexx007 Yes i use a 500mw with mdf and it cuts about 1mm per pass so this will cut much faster
2017-11-30 12:01:31 Helpful (4)We sincerely invite you to subscribe to the Invite Answer email!
If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.
Help others and be happier!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
lexx007 Yes it would but you would need to keep it light. it is more suited to a slightly higher KV motor suitable for 8060 prop or 9047 prop
2021-08-23 02:24:28 Helpful (0)