Aresby
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

Aresby 14/04/2019
I did a video on this great little screen for which there is a modified Adafruit library available. https://youtu.be/TKN9WmunCQU
3Pcs Geekcreit® OLED Shield V2.0.0 For Wemos D1 Mini 0.66" Inch 64X48 IIC I2C Two Button
US$12.99 US$23.99
2
Recommendations
Comments (0)
Aresby 21/07/2020
Not really suitable for CR2032 as the battery is so thick it eventually (after a few days) forces the soldered metal holder off the PCB (including the pads). I found that using CR2025 is a much smoother (less stress) fit. A CR2016 might work too but I haven't tested that. The small switch is nice but dainty, I don't expect to pass much current through it.
5pcs LilyPad Coin Cell Battery Holder CR2032 Battery Mount Module
US$8.39 US$10.99
0
Recommendations
Comments (0)
Aresby 21/04/2018
Connect an approx 3K3 resistor from CH_PD (Chip Enable) to VCC to enable the chip. Also, connect approx 1K5 from GPIO0 (zero) to VCC to allow it to run from the bootloader. Then it works. The manufacturer cannot ever have tested this module. Easy to fix but rather untidy finish now with two resistors soldered underneath. Still reasonable value for money but the quality is obviously poor (as is the soldering of the sockets on this module, all over the place).
ESP-01S Relay Module WiFi Smart Remote Switch Phone APP Geekcreit for Arduino - products that work with official Arduino boards
US$2.99 US$10.99
2
Recommendations
Comments (1)
Aresby 31/01/2020
This had the long metal screws to hold the screen to the front panel, good!
Transparent Shell Acrylic Case For 128X64 0.96 Inch OLED LCD LED Display Module Holder Bracket
US$0.99 US$7.99
0
Recommendations
Comments (0)
Aresby 31/01/2020
No problems with this item.
Geekcreit® 0.96 Inch 4Pin Blue Yellow IIC I2C OLED Display Module Geekcreit for Arduino - products that work with official Arduino boards
US$5.24 US$11.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
For custom circuits as part of the Wemos D1 mini setup these are great. It's the one with the LED on in the photo. See my video here: https://youtu.be/TKN9WmunCQU
5Pcs ProtoBoard Shield Expansion Board For D1 Mini Double Sided Perf Board Compatible
US$4.56 US$9.99
0
Recommendations
Comments (0)
Aresby 23/04/2019
Fantastic for video YouTube videos. You can place one either side of you to get a balanced (and bright) light. Just plug directly into your household electricity (mains) and that's it. They get fairly warm after some time but nothing to worry about. They are very bright.
50W Black Shell LED Flood Light Waterproof White Light Landscape Garden Lamp for Outdoor AC185-265V
US$16.07 US$20.99
0
Recommendations
Comments (0)
Aresby 14/03/2019
This is really professional looking equipment box and will make any electronics project very good looking. The front and rear plastic panels are easy to cut with care for cables, switches, panel meters etc. The trick is to do it slowly and gently, you can always cut away a bit more but not put the plastic back! The handle swings forward to tilt the front panel upwards to make it easier to see. It then swings underneath to make the case flat to the workbench again.
Excellway® EF01 Electronic Plastic Shell Cartridge Handle Project Case Desk Instrument 200x175x70mm
US$13.59 US$19.99
0
Recommendations
Comments (0)
50W Black Shell LED Flood Light Waterproof White Light Landscape Garden Lamp for Outdoor AC185-265V
US$16.07 US$20.99

Q: What type of connection is required for direct wiring to American 110-115 voltages?

Asked by pennington2008 on 2019-01-19 08:06:30

Aresby You could wire two in series, that would work for USA voltages.

2019-01-19 10:37:46 Helpful (0)
Submit
Answers (2)
Aresby 14/03/2019
Makes a huge difference when soldering (or desoldering using braid). It allows the solder to wet the track so much more easily. Only minor problem is that the tip eventually (after 1 year) becomes a soggy clump which is why I'm ordering another one. Definitely worth it.
Kester-186 Pen With Rosin flux FPC PCB Plate Welding Repair Tools Solder Paste
US$9.99 US$11.99
0
Recommendations
Comments (0)
Aresby 14/03/2019
A tiny sewing machine that is perfect for simple stitches (eg hems). Just an hour's practice will enable you to produce good results. Footswitch is just on/off, no speed control. Just what I needed to resize my Green Screen that I use for YouTube videos, simple hem, perfect. This might be very small but it is not a toy, it is a proper sewing machine.
Portable Home Handwork Electric Mini Sewing Machine With Led Light
US$37.99 US$45.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
Powerful chip on a tiny board. See my video here: https://youtu.be/TKN9WmunCQU
3pcs D1 Mini V3.0.0 WIFI Internet Of Things Development Board Based ESP8266 4MB Geekcreit for Arduino - products that work with official Arduino boards
US$13.02 US$19.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
Easy to use, just plug in. Can use longer or different type-K thermocouples (available here on Banggood).. See my video here: https://youtu.be/dRGX_8P_98w
Red LED DC 12V Digital Thermocouple Thermometer Temperature meter 0~999°C with Probe
US$16.06 US$26.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
The dual and triple boards are great to create a Wemos D1 mini project. See my video here: https://youtu.be/TKN9WmunCQU
3Pcs Double Socket Dual Base Shield For D1 Mini NodeMCU ESP8266 DIY PCB D1 Expansion Board
US$7.99 US$9.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
Easy to interface using SPI and the Wemos D1 Mini See here: https://youtu.be/TKN9WmunCQU
3Pcs Micro SD Card Shield For D1 Mini TF WiFi ESP8266 SD Wireless Module
US$4.99 US$8.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
Great way to power the Wemos D1 mini boards See my video here: https://youtu.be/TKN9WmunCQU
3Pcs WeMos® DC Power Shield V1.0.0 For WeMos D1 Mini
US$10.41 US$16.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
The triple base is a great start for a project so that it doesn't turn into a towering monster! See my video here: https://youtu.be/TKN9WmunCQU
3Pcs Wemos® Tripler Base Socket V1.0.0 For WEMOS D1 Mini
US$9.99 US$11.99
0
Recommendations
Comments (0)
Aresby 14/04/2019
I bought two pairs and they are very, very sharp. Far less pressure is required when using them. they must be good because the price has gone up by $1 since I bought mine!
BEST BST-109 Mini Wire Carbon Steel Cutting Pliers Electronic Hand Tools Cable Stripper Cutter
US$5.24 US$9.99
0
Recommendations
Comments (0)
Aresby 14/03/2019
The consistency of this solder paste is like toothpaste, but is grey! It turns into solder with the heat of a normal soldering iron or a hot air gun. Works great for SMD components. Don't use too much, just a smear is enough on modern PCBs and using clean SMS components.
MECHANIC Soldering Solder Welding Paste Flux SMD SMT Sn63/Pb37 Tool Soldering Iron Flux Repair Tool
US$7.99 US$9.99
0
Recommendations
Comments (0)
Aresby 05/01/2019
You can use libraries written by others, which usually work well enough, or write your own as all it requires is 5 bytes of data using I2C, very easy to create a fully-fledged radio with an LCD, multiple memory tuning, rotary encoder for manual tuning or just a couple of buttons. An ideal central module for a much bigger, beginners' project.
TEA5767 FM Stereo Radio Module 76-108MHZ With Antenna
US$10.39 US$15.99
0
Recommendations
Comments (0)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe