sqfoofs
My Contents
All Messages
Reviews
Comments
Answers
Questions

All Messages

Eachine EV200D 1280*720 5.8G 72CH True Diversity FPV Goggles HD Port in 2D/3D Built-in DVR With 18650 Battery Case for RC Drone
US$325.99 US$385.19

Q: will these be able to accommodate different diopter lenses? Would I be able to put RHO lenses in them? *****

Asked by sqfoofs on 2018-09-27 09:38:50

Tyburn Yes you be able to put RHO lenses, on thé ev200d you can put fatshart gifle

2020-02-07 02:29:36 Helpful (0)
Submit
Answers (1)
sqfoofs 16/10/2018
I have not really flown with this yet - only plugged it and tried a few things in to check that it works. The camera works well and I am happy with it so far, but before you plug it in to ANYTHING, check the wires in the plug. Mine were completely reversed from what the picture and documentation show. I did a little research and thanks to another helpful post here, I was able to carefully pull the wires out of the plug and re-insert them in the correct order for my aurora 1000. Video works, OSD works. I can understand that this is not the exact replacement for the original camera in the Aurora 100, but the wires were not even in the same order as the documentation and photos - you can't trust that you can just plug it in to whatever it is intended for. 3 stars for quality - the camera works well, but no one should have to double check and change the wiring of a product. Unless you pay attention to the wires and check them carefully, you could ruin something just by plugging this in.
Eachine TX05 0.01/5/25/50/100/250mW Switchable w/ OSD AIO 5.8G 72CH VTX 600TVL NTSC Mini FPV Camera for RC Drone
US$32.00 US$64.99
1
Recommendations
Comments (0)
sqfoofs 28/02/2019
just got this - seems to work well. + Charges with just the USB so don't worry about getting the european adapter - you don't really need it. (FYI you can not operate it while the USB is plugged into the computer - I haven't tried the software that was linked in one of the questions) + The stand seems solid and the anti-slip pads on the bottom are good, but it would be nice if the base was a little larger, but that's not a problem. + provides more than enough magnification for me to solder tiny stuff, even with the optics raised as far away as possible from the stand (approximately 12 cm). + there's plenty of room under it to solder stuff and it's MUCH better than wearing the jeweller's magnifier that I have been using. + the depth of focus is shallow but not too shallow (so it's good!) + The focus knob works well - focus and resolution are quite good for using this to do small work + I like that the light can be adjusted and even turned off to allow use of other light sources like natural light or a desk lamp + for versatility, you could easily find a way to mount the unit on a different stand if you really wanted to (haven't tried it, but maybe using one of those third hand tools or something...? the screen/lens unit weighs about 180 grams) Overall - comparing this to jeweller's glasses/magnifier for around the same price (the kind that you wear), this is better! way more comfortable, less finicky and works well!
G600 Digital 1-600X 3.6MP 4.3inch HD LCD Display Microscope Continuous Magnifier Upgrade Version
US$53.41 US$67.99
0
Recommendations
Comments (0)
sqfoofs 28/02/2019
ok
Geekcreit® DC-DC Boost Buck Adjustable Step Up Step Down Automatic Converter XL6009 Module Suitable For Solar Panel
US$1.99 US$8.99
0
Recommendations
Comments (0)
sqfoofs 16/10/2018
good
Eachine Aurora 90 Mini FPV Racer RC Drone Frame Kit Spare Part Screws Package
US$6.99 US$8.99
0
Recommendations
Comments (0)
sqfoofs 16/10/2018
good
Eachine Aurora 100 Mini Brushless FPV Racer RC Drone Frame Kit Spare Part M2*6 Screws Set
US$5.99 US$7.99
0
Recommendations
Comments (0)
sqfoofs 01/10/2018
dense foam, works great, fits on my Q X7 perfectly and works well. Very simple and does the job well. I use them with this case: https://www.banggood.com/Realacc-Zipper-Handbag-Hard-Case-For-Frsky-X9D-FlySky-i6S-i6-DJI-Transmitter-p-1098445.html?
2 PCS EVA Transmitter Throttle Protection Sponge Compatible FUTABA JR Frsky Flysky for RC Drone
US$2.04 US$3.09
0
Recommendations
Comments (0)
sqfoofs 01/10/2018
mine came with one big block of foam that was perforated. No problem pulling out little bits to make it fit my Q X7 perfectly. The inside pocket is great for the small stuff. get some of these to protect your sticks: https://www.banggood.com/2-PCS-EVA-Transmitter-Throttle-Protection-Sponge-Compatible-FUTABA-JR-Frsky-Flysky-for-RC-Drone-p-1243954.html?
Realacc Zipper Handbag Hard Case For Frsky X7 X9D FlySky i6S DJI Remote Transmitter
US$20.19 US$32.00
0
Recommendations
Comments (0)
sqfoofs 26/06/2018
simple use. voltage reading matches my voltmeter, so I assume it's accurate!
Battery Voltage Meter Tester Battery Monitor Buzzer Alarm For 1S-8S Lipo Battery
US$7.34 US$10.99
0
Recommendations
Comments (0)
sqfoofs 20/06/2018
works well
RJXHOBBY 4pcs 250x30mm FPV Silicon Anti-Slip Mat Battery Adhesive Tape for FPV Racing Drone
US$13.59 US$19.99
0
Recommendations
Comments (0)
sqfoofs 20/06/2018
I have been using this without any problem. Works well on my 2S batteries with my Hitec chargers
1S-3S XT30 Plug Parallel Charging Board Para Board for B6 Charger
US$13.64 US$15.99
0
Recommendations
Comments (0)
sqfoofs 15/03/2018
very thin - you need to be careful not to drop or hit them because they will break.
100pcs N50 Round Disc 12 x 1mm Magnet Rare Earth Neodymium Magnetic Toys
US$8.73 US$10.47
0
Recommendations
Comments (0)
sqfoofs 15/03/2018
as expected. strong magnets. The hole and countersink is just right for small screws.
4pcs N52 20*5mm Counterbore Hole 5mm Neodymium Super Strong Magnets
US$5.68 US$10.99
0
Recommendations
Comments (0)
sqfoofs 16/02/2018
I bought this to play around with making simple experimental foamie planes. I have a Taranix qx7 and managed to bind with this using the iRange IRX4 Plus module. It seems to work just fine, responds as expected. no issues. There are a lot of videos out there about how to bind various radios with this, but I suspect most of them are confusing linking with binding (typically, you bind once and from then on, you link which happens when you turn things on) If you are having trouble, it BINDS when the red light is flashing rapidly. the IRX4 is in bind mode when its red light is flashing. you need to coordinate this so that the v911 is flashing rapidly while the module is also flashing. It requires timing and it is tricky, but it does work.
WLtoys V911 V911-1 V911-PRO V911-V2 Helicopter PCB Board Spare Parts
US$10.88
0
Recommendations
Comments (0)
sqfoofs 16/02/2018
as described. not much more to say
Gear Box 0720 Coreless CW Motor + Propeller Combo Set For RC Models DIY Parkfly Airplane
US$4.00 US$13.19
0
Recommendations
Comments (0)
sqfoofs 15/02/2018
It comes with instructions that are translated well and it's easy to set up a model and bind. It fits perfectly in my taranis x7 and looks good and appears to be made well.
iRangeX IRX4 Plus 2.4G CC2500 NRF24L01 A7105 CYRF6936 4 IN 1 Multiprotocol ARM TX Module With Case
US$31.99 US$67.99
0
Recommendations
Comments (0)
sqfoofs 01/02/2018
These will flex a bit but they are half the weight of the aluminum circular guards and they leave PLENTY of room for the props. Mine haven't broken yet.
4 PCS Eachine Propeller Guard For Aurora 100 Mini FPV Racing RC Drone 1102 1103 1104 1105 Brushless Motor
US$3.54 US$8.99
0
Recommendations
Comments (0)
sqfoofs 01/02/2018
they don't flex much at all and feel sturdy, but they are quite thin. If you need to bend them back several times, maybe that thin aluminum might fatigue, but these seem to be sturdy enough (they are twice the weight as some of the plastic guards but still relatively light). You might not want to put these on one of those super thin frames because I suspect they would transfer the energy to the frame due to their stiffness. On the other side, a light to moderate crash isn't going to bend these into the props. I had some success mounting these to the Eachine Aurora 100. They leave just enough room for the props. If they were flexible plastic, I would say not enough room but these do not seem to flex. However, to get the mounted I had to put the front guards underneath of the frame and the back guards on top, between the frame and motor. it means the back motors will be 1mm higher if you try that. They just touched doing that but seem to be ok. I didn't keep the configuration long enough to really test it well. They are strong, they look great but I put Value for Price lower because they are more than 4 times the price of the plastic guards...but maybe you think that doesn't matter.
PG50 2 Inch 50mm Propeller Protective Guard Compatible with 1102/1103/1104/1105 Motor
US$2.99
1
Recommendations
Comments (0)
sqfoofs 01/02/2018
same as the original. I had to replace one that seemed to be shorted. I think I found the problem with the old motor after I replaced it. New one works fine
DYS BE1102 7800KV 10000KV Brushless Motor for RC Drone FPV Racing
US$10.99
0
Recommendations
Comments (0)
sqfoofs 01/02/2018
Edges are smooth and it comes with extra motor screws. no complaints. That's all I can say because I have not installed it yet - I will when I smash my original! (what can I say...I'm clumsy and I know it will happen)
Eachine Aurora 100 Brushless FPV Racer RC Drone Spare Part 2mm 2.5mm Bottom Plate 3K Carbon Fiber
US$10.39 US$15.99
0
Recommendations
Comments (0)

You are the expert,can you help?

We sincerely invite you to subscribe to the Invite Answer email!

If you subscribe, we will invite you via email to answer questions people have about products. By subscribing you]ll also earn the "Helpful Badge"! You can unsubscribe at any time on the privacy settings page.

Help others and be happier!

  • Subscribe

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.Specific people will also have their own exclusive badge.
CEO Badge

The CEO Badge is owned only by the boss of Banggood.

Badges you can earn are coming soon
  • OK

About Badges

Badges are related to the community, and users earn badges by creating quality content, completing missions, or by participating in special activities.

Helpful Badges

The Badge is awarded to users who are subscribed to the Invite Answer email and signifies their gratitude to help others. The badge appearance upgrades as the user helps more people.
  • OK

Thank you for subscribing! You have also earned a badge!

  • View It

Thank you! Your answer will help ###name### and ###num### other people!

Check awaiting answers to see more people who need help.

  • OK

Thank you! Your answer will help ###name### and ###num### other people!

Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!

  • Subscribe

Are you ready to help?

We invite you to subscribe to our Invite Answer email!

Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.

  • Subscribe