Customer Reviews

4.95 out of 5
See all 119 reviews
Write a Review
  • All Reviews (119)
  • Image (21)
  • Video (2)
  • All Star
    • All Star(119)
    • 5 Star(113)
    • 4 Star(6)
    • 3 Star(0)
    • 2 Star(0)
    • 1 Star(0)
Sort by:
Top Review
  • Top Review
  • Most Helpful
  • Most Recent
Reviews only from your country (United Kingdom)
|
Show Original

A part of the review has been auto-translated.

  • 21/07/2021

    Does the job and all components were in the kit. Excellent.

    Comments
    Show Original
  • 06/08/2017

    I bought 3 pre-order kits. They now cost less. I was thinking of using them to feed small projects to replace batteries. I think it can be fed with voltages below 24 Vac. I did a little test. Without load: Vac = 19,6 Volt --- Vcc out = 21,2 Volt With load (8 ohm and Vcc = 8 Volt then 1 A) Vac = 18,86 Volt --- Vcc (without load) = 8,04 Volt --- Vcc (with load) = 7,98 Volt. Note: The maximum current before the protection is: 8.72Volt / 8ohm = 1.09 Amper. I also tried with a lower power supply. Without load: Vac = 16,4 Volt --- Vcc out = 17,1 Volt With load (8 ohm and Vcc = 4 Volt then 0.5 A) --- Vcc (without load) = 4,02 Volt Vcc (with load) = 3,99 Volt. Considerations: I could not measure the ripple with my toy oscilloscope. The output voltage setting is rough. A multigiro or 2 in series potentiometer is preferable for a more accurate adjustment.

    Comments
    Show Original
  • 12/09/2017

    useful and versatile power supply Kit from Hiland. it use the classic LM317 voltage regulator IC. the pcb is very well made. please take care that the heatsink it is not included. good practice kit. suggested kit alimentatore con il classico regolatore Lm317; il PCB è ben fatto. Attenzione che il dissipatore non è incluso. Kit utile e consigliato per fare pratica di saldatura. consigliato

    Comments
    Show Original
  • 17/08/2017

    A useful and easy to assemble source with the well-known LM317 integrated circuit, voltage regulation between 0-30V and, surprise, current setting between 0-1A. Very useful for DIY projects with consumption up to 1A. You can use the cooling assembly made of an aluminum radiator and fan (24V) found on banggood.com. Excellent Banggood!

    Comments
    Show Original
  • 26/04/2019

    mounted all parts on pcb, tested on 24ac input.. posible to control V and I with potentiometer but the output voltage is max 6,5V ?? some problem with transistors or IC. will be easy to repair if producer attached el. drawing for pcb. lm317 get hot on o,5A load, need good bigest Radiator

    Comments
    Show Original
  • 06/04/2019

    Stavebnice lineárního regulovatelného zdroej 0-30V 0-1A. Perfektně vyrobena deska plošných spojů. Otvory pro osazení součástek jsou prokoveny a upraveny pro snadné pájení. Koupil jsem dva kusy - vše OK. Uvítal bych dodání schéma pro snadnější hledání závady.

    Comments
    Show Original
  • 24/06/2018

    I got all the resistors and small capacitors in and ready to solder and then I remembered what one U-Tuber said "test test and retest at any point that will provide useful results it is much easier to test early than to troubleshoot once it is built" so I pulled all the components out and tested them so now I can restart my build.

    Comments
    Show Original
  • 18/03/2018

    Arrived in good conditions. Assembled (to easy actually) and testing whith old transformer 14.4 v single. Looks like work properly. Waiting to arrive new double transformer 12-0-12v AC 30w. Order new kitt to make one home made power bench supply.

    Comments
    Show Original
  • 26/02/2018

    i'm a beginner and it took me about 1h to solder and verify this kit. (including veryfing resistor value and sorting them ). As i had not an AC 24V input, i tried with DC. Values are not really as advertised but this could be related to the absence of heatsink ! (max voltage was 18V with 24v dc input) - i may need to reinspect everything. I first though the led was not working but if you read the description, it lights up only when the current limit is reached ! I did'n pay attention to the "without heatsink" note... As it seems to be mandatory to reach the advertised values , this should be included. Note : i added a tulipe support for the LM358P IC

    Comments
    Show Original
  • 23/10/2019

    Ok, semble conforme, pas encore montée ni testée, les potars semblent très très cheap !

    Comments
    Show Original
Show:

    Total 0 pages

    Go to page

    Go

    You might be interested in

    recommendation for you
    • £10.03
    • £11.79
    • £10.32
    • £18.14
    • £9.58
    • £14.01
    • £8.36
    • £9.58
    • £19.91
    • £18.01
    • £14.01
    • £3.68
    • £28.76
    • £5.01
    • £4.42
    • £14.01
    • £18.43
    • £2.50